Just How to Set up a Bathtub: Set Up an Acrylic Bathtub and Bathtub Surround
Just How to Set up a Bathtub: Set Up an Acrylic Bathtub and Bathtub Surround
Blog Article
We have discovered this article involving How to Install a Bathtub below on the internet and accepted it made good sense to talk about it with you in this article.
Mounting a bathtub isn't precisely rocket science, yet it does require solid plumbing, woodworking, and also in some cases, tiling abilities. Changing an old bathtub with a new one is likewise a reasonably difficult job. If the old bathtub is conveniently accessible, the job can move immediately; if you need to open up a wall surface to get rid of the old tub as well as place the brand-new bath tub, the task is much harder. In either situation, the task is within a residence handyman's skills, although you will need an assistant to vacate the old bathtub and set in the new one. Make certain you have actually certified on your own for the job and are comfortable attempting it. Instead of working with a contractor to take control of a halfway-completed task, it is far better to consider utilizing one prior to you start. Opportunities are you might require a specialist plumber to make tube links.
This write-up will certainly assist you set up a brand-new bath tub in your washroom if you have actually currently gotten a brand-new bathtub as well as do not require to alter the plan of your previous water system pipelines.
Your devices as well as product checklist ought to make up the following:
Removing Old Touches
If you require to replace old taps with new ones as a part of your installation, then the first thing you should do is separate the water. After doing so, activate the faucets to drain pipes any type of water staying in the system. The process of removing the existing faucets can be fairly troublesome due to the limited gain access to that is commonly the situation.
Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipes to the faucets. Have a towel prepared for the staying water that will originate from the pipes. As soon as the supply pipelines have been gotten rid of, utilize the same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the single taps from transforming during this procedure. When the taps have actually been removed, the holes in the bath/basin will certainly have to be cleansed of any type of old sealing substance.
Before going on to fit the new faucets, compare the pipe links on the old taps to the brand-new taps. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will require a plastic connector to stop damage to the string. One end of the connector fits on the plastic tail of the tap and also the other end gives a connection to the current supply pipes.
If you require to fit a monobloc, then you will certainly require decreasing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, position the tap in the placing hole in the bath/basin making certain that the washers remain in area between the faucet and the sink. Protect the faucet in place with the maker provided backnut. When the faucet is securely in place, the supply pipelines can be attached to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with normal faucet adapters. The former type needs to be connected to the tap finishes initially, tightening just by hand. The supply pipelines can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Mounting the Bathtub
Using the two wood boards under its feet, position the bathtub in the needed setting. The wood boards are helpful in uniformly spreading out the weight of the bath tub over the location of the boards instead of focusing all the weight onto four tiny factors.
The following objective is to ensure that the bath tub is leveled all round. This can be accomplished by examining the level and also adjusting the feet on the bathtub up until the level reads level.
To set up taps, fit all-time low of the outermost adaptable tap connector to the suitable supply pipe by making a compression sign up with; after that do the very same for the various other faucet.
Switch on the water supply and inspect all joints as well as new pipework for leakages and also tighten them if essential. Load the bath tub as well as additionally examine the overflow electrical outlet and the normal outlet for leakages.
Ultimately, deal with the bathroom paneling as explained in the maker's user's manual. Tiling and also sealing around the bathtub should wait until the bathtub has been used at least when as this will certainly resolve it right into its last placement.
Planning for the Setup
First of all, the supporting frame provided with the bathroom must be fitted (if needed) according to the maker's guidelines. Next off, fit the taps or mixer to the tub. When fitting the tap block, it is important to make sure that if the faucet features a plastic washing machine, it is fitted between the bath and the faucets. On a plastic bathroom, it is likewise practical to fit a supporting plate under the taps device to stop stress on the bathtub.
Fit the flexible faucet adapters to the bottom of both taps using 2 nuts and also olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet with the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make certain you use every one of the supplied washers.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bath need to currently be ready to be suited its final placement.
Tiling Around the Bathtub
In the location where the bath fulfills the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate sufficient to crack a rigid seal, triggering the water to penetrate the wall surface between the bathroom and the tiling, bring about problems with wetness as well as feasible leaks to the ceiling listed below.
You can select from a selection of coloured sealants to assimilate your fixtures and also fittings. They are offered in tubes and cartridges, as well as are capable of securing voids as much as a size of 3mm (1/8 inch). If you have a larger space to fill, you can load it with spins of soaked paper or soft rope. Remember to constantly load the bathtub with water prior to securing, to allow for the activity experienced when the tub is in usage. The sealant can split rather early if you do not think about this movement before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are likewise conveniently available on the marketplace. It is suggested to fit the tiles utilizing waterproof or waterproof adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I found that blog posting about How to Install a Bathtub while exploring the search engines. Sharing is caring. Helping others is fun. Thanks a lot for taking the time to read it.
Book With Us Today!
Report this page